product categories
MCOM WLCD
MCOMWLCD based water level indicator
is equipped with best quality material & latest technology. It shows 3
levels of tank (Full, ½, 10%) through high glow LED lights. We use long life
molded sensors built with high grade stainless steel.
The indicator is
specifically designed to use where water is taken from any regular source of
water like earth water or irregular source like corporation pipeline. These are
available in different specifications to meet the requirements of Our Clients.
Generally, especially during summers, water is
supplied at very odd hours of the day or for a very small period of time. Normally, you
will have to be available at that time to switch on the motor. Then keep in
mind, whether the tank would have been full or not and after all these, still
you are not sure whether the tank is full or not. MCOM Automatic water level controller once
installed, system automatically takes care of your motor / pump and thus you need not worry about,
whether water is there in the tank or not.
- Features
- Specifications
- Applications
- Additional Information
· Programmable Timer
·
Float Switch Sensors / No Scaling on Sensor (Carbon
Free)
We are best in after
sale services also and our aim is to provide benchmark services in the
industry. Our few beneficial points are mentioned below:
·
High Quality
·
Quick Service
·
Latest Technology
·
Customer Satisfaction
Specialty: We provide float
switch sensors: no scaling/ depositing of any salt [carbon free] on the surface
of sensors, even after years.
The Concept of Water Level Controller System:
The Water Level Controller System is an Electronic Equipment which when electrically connected to the starter of any given pump set motor will control the operation of the pump set depending upon the water level in the Source and Destination Storage Tank.AdvancedAutomatic “WATER LEVEL CONTROLLER” unit Manufactured by “MODERN COMMUNICATION TECHNOLOGY “. This system when electrically connected to an Pumpset starter, performsthe following functions automatically:
- Switches ON
the Pumpset when Water level drops below pre-set level (i.e. T2 level) in Overhead
Tank.
- Switches
OFF the Pumpset when Water level in Overhead Tank becomes full (i.e. T1
level).
- Switches
OFF the Pump set when Water level is low in Sump/Well/Borewell (i.e. S2
level).
- Switches ON
the Pump set when there is sufficient water in the Sump/ Well / Bore well
(i.e. S1 level).
- Switches
OFF the Pump set when there is a Dry run (i.e. when Water is not being
pumped into Overhead Tank due to any reason).
- All these
functions are automatically performed. Manual interference is absolutely
not required.
- Manual operation is also possible if and when required by operating the switch in Manual position.
Specifications
Input Voltage (AC) : 220 – 270 VAC, 50 Hz
On voltage (Cold Start): 250 VAC
Pump Current Range : 5 Amp.
Resetting mode :
Manual by OFF switch.
Output Relay Contact
Relay Mechanical life : 10 lac operations
Dielectric Strength : 2.2 KV, 50 Hz for 1 min
Enclosure & Mounting
Enclosure Material : ABS Enclosure
• Mounting : Wall Mounting with 4 screw M4 × 15 mm
• Temperature : 5 to 60°C
• Humidity : Up to 90% RH
9.
Dimensions & Weight
• L × W × D (mm) : 70 x 100 x 45 mm
• Power
Consumption : Less than 1 Watts
• Weights : 450 gms.
Applications
Industrial
Domestic
Connection
Diagram
|
INPUT 230 VOLT |
PUMP START |
PUMP STOP |
SIX LEVEL SENSORS |
|
TWO WIRE FOR LINE AND NEUTRAL SUPPLY, RED FOR
LINE, BLACK FOR NEUTRAL |
TWO GREEN WIRE |
TWO BLACK WIRE |
THREE SENSORS FOR OVERHEAD TANK AND THREE FOR
LOWER TANK, TWO-TWO WHITEWIRE FOR EACH SENSOR. |
Copyright © 2024. MODERN COMMUNICATION TECHNOLOGY. All rights reserved.